Juniper JN0-690 Value Pack (Frequently Bought Together)

Which CLI command applies the candidate configuration to the active configuration?

• A. copy run start
• B. merge
• C. load
• D. commit

Click the Exhibit button.
-- Exhibit -
Slot 0 information: State Online Total CPU DRAM ---- CPU less FPC ---Start time 2012-07-07 03:21:00 UTC Uptime 27 minutes, 51 seconds Slot 1 information: State Present Reason --- Hardware Not In Right Slot --Slot 2 information: State Online Total CPU DRAM 32 MB Start time 2012-07-07 03:20:59 UTC Uptime 27 minutes, 52 seconds Slot 3 information: State Present Reason --- Hardware Not Supported --Total CPU DRAM 0 MB Slot 6 information: State Online Total CPU DRAM 32 MB Start time 2012-07-07 03:21:01 UTC Uptime 27 minutes, 50 seconds
-- Exhibit -
Referring to the exhibit, which three statements are true? (Choose three.)

• A. The Flexible PIC Concentrator (FPC) in slot 6 is online and working.
• B. The Flexible PIC Concentrator (FPC) in slot 1 is not installed properly for this chassis.
• C. The Control Board in slot 0 has a missing CPU.
• D. The Control Board in slot 6 is online and working.
• E. The card in slot 3 is not supported by the chassis.

What controls the CLI process?

• A. management daemon
• B. chassis control daemon
• C. device control daemon
• D. routing protocol process

-- Exhibit -
[edit]
user@router# show interfaces
ge-1/1/2 {
gigether-options {
802.3ad ae0;
}
}
ge-1/1/3 {
gigether-options {
802.3ad ae0;
}
}
ae0 {
unit 0 {
family bridge {
interface-mode trunk;
vlan-id-list 100;
}
}
}
-- Exhibit -
You are asked to configure a LAG. You configure and commit the configuration as shown in the exhibit. When verifying your ae0 interface, you encounter the following error:
[edit] user@router# run show interfaces ae0 error: device ae0 not found
Which command would you use to resolve this problem?

• A. set interfaces ae0 aggregated-ether-options lacp active
• B. set chassis alarm ethernet link-down ignore
• C. set chassis aggregated-devices ethernet device-count 1
• D. set chassis network-services ethernet

-- Exhibit -[edit] user@R1# run show interfaces ge-1/1/2 terse Interface Admin Link Proto Local Remote ge-1/1/2 up up ge-1/1/2.0 up up aenet --> ae0.0
[edit] user@R1# run show interfaces ge-1/1/3 terse Interface Admin Link Proto Local Remote ge-1/1/3 up up ge-1/1/3.0 up up aenet --> ae0.0
[edit]
user@R1# run show interfaces ae0 terse
Interface Admin Link Proto Local Remote
ae0 up down
ae0.0 up down bridge
[edit]
user@R1# show interfaces ae0
aggregated-ether-options {
lacp {
periodic slow;
system-priority 200;
}
}
unit 0 {
family bridge {
interface-mode trunk;
vlan-id-list 100;
}
}
**************************************************************************
[edit]
user@R2# run show interfaces ge-1/1/2 terse
Interface Admin Link Proto Local Remote
ge-1/1/2 up up
ge-1/1/2.0 up up aenet --> ae0.0
[edit]
user@R2# run show interfaces ge-1/1/3 terse
Interface Admin Link Proto Local Remote
ge-1/1/3 up up
ge-1/1/3.0 up up aenet --> ae0.0
[edit]
user@R2# run show interfaces ae0 terse
Interface Admin Link Proto Local Remote
ae0 up down
ae0.0 up down bridge
[edit]
user@R2# show interfaces ae0
aggregated-ether-options {
lacp {
periodic fast;
system-priority 100;
}
}
unit 0 {
family bridge {
interface-mode trunk;
vlan-id-list 100;
}
}
-- Exhibit --
You have configured a LAG and are now enabling LACP on the ae0 interface. You have configured and committed the configuration as shown in the exhibit. However, the exhibit also shows that the ae0 interface is now in the up/down state.
What must you do to resolve this problem?

• A. Configure R1's LACP configuration as active.
• B. Configure R2's LACP configuration as passive.
• C. Configure both routers' ae0 LACP configuration to periodic fast.
• D. Change the LACP system-priority of R1 to 300.